Elevate PVC Split Pipe Boots are factory-fabricated flashings made from high-performance Elevate PVC with DuPont Elvaloy® KEE roofing membrane. The split boot is specifically designed for flashing round penetrations of various sizes from 1" to 12" (25 mm to 305 mm). The split tab design allows the boot to be used for flash pipe penetrations with limited or no access from above the penetration. This pipe boot design eliminates the need to field fabricate with PVC Unsupported Flashing, thus lessening labor and increasing the performance of the system.
Elevate PVC Universal Pipe Flashings are factory-fabricated flashings made from high-performance Elevate PVC with DuPont Elvaloy® KEE roofing membrane. The universal boot is specifically designed for the flashing of round penetrations. PVC Universal Pipe Flashing fits various penetrations from 1" (25 mm) to 4½" (114.3 mm). The Elevate PVC Universal Pipe Flashing must be cut to correct size before installation..
Elevate PVC T-Joint Covers are a flexible, non-reinforced, flashing membrane made with DuPont Elvaloy® KEE. They are designed to cover and seal T-joints formed at seam intersections and angle changes 1:12 or greater for Elevate PVC reinforced membranes..
Elevate PVC Inside and Outside Molded Corners are made with non-reinforced Dupont Elvaloy® KEE. The PVC Inside and Outside Molded Corners were specifically designed for flashing inside and outside corners on curbs, parapets, scuppers, and other areas where an inside or outside factory formed corner flashing is appropriate..
Elevate PVC 8" Cover Strip is a pre-cut 8" (203 mm) wide cover strip made from 60 mils (1.5 mm) thick, reinforced Elevate PVC membrane. This heat weldable cover strip can be used as a cover for intermediate or perimeter mechanical attachment on PVC systems as well as for stripping in PVC Coated Metal roof edge details and Elevate PVC XR membrane end laps.
Elevate PVC Unsupported Flashing is a non-reinforced PVC membrane made with DuPont Elvaloy® KEE, used in roofing applications where Elevate pre-formed PVC accessory products are not appropriate. Elevate PVC Unsupported Flashing is available in 50' (15.2 m) rolls..
The Elevate PVC X-Tred Walkway Pad is a highly specialized UV resistant pad made from PVC and designed to provide protection from essential rooftop services and traffic and maintain the integrity of the existing roof surface. PVC X-Tred Walkway Pads can be installed loose-laid on top of the existing PVC adhered roof assembly, making installation simple
The Elevate PVC Walkway Pad is a reinforced thermoplastic material intended for use as a traffic bearing surface over Elevate PVC roofing installations. The pad is produced in 30" (762 mm) wide by 60' (18.3 m) long rolls; gray in color or safety yellow to highlight traffic and maintenance pathways. The pad has a textured top surface and a smooth bottom surface for easy welding to the Elevate PVC roof membrane
Twin Jet is a two-component, low-rise polyurethane adhesive applied in bead pattern for the attachment of Elevate approved roof insulations. It may also be used in bead or spatter pattern for the attachment of Elevate PVC XR membrane to acceptable horizontal substrates, per Elevate specifications. Twin Jet is packaged in portable pressurized canisters, allowing extrusion of Part 1 and Part 2 to the gun and mix tip assembly.
Elevate PVC LVOC Bonding Adhesive is a bonding adhesive designed for bonding Elevate PVC membranes and flashings to wood, metal, masonry, and other acceptable substrates..
Elevate PVC Clear Cut Edge Sealant is an optional treatment used for sealing cut edges of the PVC membrane where scrim reinforcement is exposed..
Elevate PVC Water Based Bonding Adhesive is designed to adhere Elevate PVC and Elevate PVC XR membranes and flashings to wood, metal, masonry, and other acceptable substrates.
Elevate I.S.O. Spray R Adhesive is a two-component low rise polyurethane adhesive engineered to adhere fleece-backed Elevate PVC XR membranes to acceptable substrates. Elevate I.S.O. Spray R Adhesive is mixed and dispensed by high or low-pressure pump/proportioning units capable of mix/meter/dispensing two-component polyurethanes in full spray application and/or continuous bead extrusion.
Elevate XR Stick Adhesive is a two-component, low-rise polyurethane adhesive designed to attach Elevate PVC XR fleece-backed roofing membranes to a variety of acceptable substrates as allowed by Elevate specifications. XR Stick (cartridges) can be dispensed using various Elevate approved hand or multi bead electric dispensing units.
Elevate PVC Clad Metal is made from a 25 mil DuPont Elvaloy® membrane factory laminated to hot-dipped 24 ga. G-90 galvanized steel. Elevate PVC Clad Metal can function as a flashing component for the Elevate PVC System.
Elevate PVC InvisiWeld Plates are designed to secure roof insulation and Elevate PVC roof membranes. The plates are 3" (76 mm) (nominal) round, and made with specially formulated, coated galvanized steel. The plates are installed with Elevate All-Purpose, Heavy Duty, Concrete Drive, or Purlin fasteners into steel, wood, or structural concrete roof decks.
Your response helps us make our online experience better to provide content that is specific to your role.
Thank you. Your response helps us make our online experience better to provide content that is specific to your role.